View ATZB-RF-212B-0-CN-14_8001497.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

zigbit 900mhz wireless modules atzb -rf-2 12b -0-cn datasheet features ? c ompact size ( 3 0.0 x 20.0mm ) ? mcu less transceiver module with spi interface ? high rx sensitivity ( - 103 dbm) ? outperforming link budget (up to +112db) ? up to + 9.0 dbm output power ? very low power consumption: ? 8.7 ma in rx mode (1) ? 27 ma in tx mode (1) ? 0. 7 a in sleep mode (2) ? internal clock o utput ? preassigned atme l ? mac address that can be used on end product ? capability to use mac address into the internal eeprom ? ieee ? 802.15.4 compliant t ransceiver ? 900m hz ism band ? serial bootloader ? rapid design - in with built - in chip antenna ? rf test point using ms - 147 rf connector ? small physical footprint and low profile for optimum fit in very small application boards ? mesh networking capability ? easy - to - use low cost development kit ? single source of support for hw and sw ? worldwide license - free operation note: 1. rx rpc enabled (for rx cur rent), phy_tx_pwr=0x0 (for tx current) . 2. controller sleep mode : sleep_mode_pwr_down . 42269b ? wireless ? 07 /2014
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 2 table of contents 1. introduction ........................................................................................ 3 1.1 summary ........................................................................................................... 3 1.2 applications ....................................................................................................... 3 1.3 abbreviation s and acronyms ............................................................................ 4 1.4 related documents ........................................................................................... 5 2. zigbit module overview ..................................................................... 6 2.1 overview ........................................................................................................... 6 3. specification ....................................................................................... 8 3.1 electrical characteristics ................................................................................... 8 3.1.1 absolute maximum ratings ................................................................ 8 3.1.2 power supply ...................................................................................... 8 3.1.3 rf characteristics .............................................................................. 9 3.2 physical/environmental characteristics and outline ....................................... 10 3.3 pin configuration ............................................................................................. 10 3.4 antenn a orientation recommendation ........................................................... 11 3.5 mounting information ...................................................................................... 11 3.6 soldering profile .............................................................................................. 14 4. schemat ics ...................................................................................... 15 4.1 handling instructions ....................................................................................... 17 4.2 general recommendations ............................................................................ 17 5. p ersistence memory ........................................................................ 18 6. ordering information ........................................................................ 19 7. agency certifications ....................................................................... 20 7.1 unit ed states (fcc) ........................................................................................ 20 7.2 european union (etsi) ................................................................................... 20 7.3 industry canada (ic) compliance statements ................................................ 21 8. revision history ............................................................................... 22
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 3 1. introduction 1.1 summary atzb - rf - 212b -0- cn zigbit ? is an ultra- compact and low - power 900mhz ieee 802.15.4/zigbee ? oem module from atmel. based on the innovative mixed - signal hardware platform from atmel, this module uses the at86rf212b [3] 700/800/900mhz ism band transceiver alone on a very compact module design that provides the customer to integrate the module to any of the recommended atmel microcontrollers that the application fits . the radio transceiver provides high data rates from 20kb/s up to 1 mb/s, frame handling, outstanding receiver sensitivity and high transmit output power enabling a very robust wireless communication. the module is designed for wireless sensing, monitoring, control, data acquisitio n applications, to name a few. this zigbit module eliminates the need for costly and time - consuming rf development, and shortens time - to - market for wireless applications. the module has a n ms - 147 rf connector that can be used as an rf test port. the built - in chip antenna is designed and tuned for the zigbit design to enable quick integration of the zigbit into any application. 1.2 applications the zigbit module is compatible with robust ieee 802.15.4/zigbee stack that supports a self - healing, self - organizing mesh network, while optimizing network traffic and minimizing power consumption. for detailed software support information, visit http://www.atmel.com/products/wireless . the applications include, but are not limited to: ? building automation and monitoring ? lighting controls ? wireless smoke - and co - detectors ? structural integrity monitoring ? hvac monitoring and control ? inventory management ? environmental monitoring ? security ? water metering ? i ndustrial monitoring ? machinery condition and performance monitoring ? monitoring of plant system parameters such as temperature, pressure, flow, tank level, humidity, vibration, etc. ? automated meter reading (amr)
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 4 1.3 abbreviations and a cronyms adc analog - to - di gital converter api application programming interface dc direct current dtr data terminal ready eeprom electrically erasable programmable read - only memory esd electrostatic discharge gpio general purpose i nput/output haf high frequency hvac heating, ventilating, and air conditioning hw hardware i 2 c inter - integrated circuit ieee institute of electrical and electronics engineers irq interrupt request ism industrial, scientific , and medical radio band jtag digital interface for debugging of embedded device, also known as ieee 1149.1 standard interface mac medium access control layer mcu microcontroller unit. in this document it also means the processor, which is the core of a zigbit module nre network layer oem original equipment manufacturer ota over - the - air upgrade pa power amplifier pcb printed circuit board per package error ratio ram random access memory rf radio frequency rpc reduced power consumption rts/cts request to send/ clear to send rx receiver sma surface mount assembly soc system on chip spi serial peripheral interface sw software ttm time - to - market tx transmitter uart universal asynchronous receiver/transmitter usart universal synchronous/asynchronous receiver/transmitter usb universal serial bus zigbee, zigbee pro wireless networking standards targeted at low - power applications 802.15.4 the ieee 802.15.4 - 2003 standard applicable to low - rate wireless personal area network
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 5 1.4 related d ocuments [1] ieee std 802.15.4 - 2003 ieee standard for information technology - part 15.4 wireless medium access control (mac) and physical layer (phy) specifications for low - rate wireless personal area networks (lr - wpans) . [2] zigbee specification. zigbee document 053474r17, october 19, 2007 . [3] at86rf2 12b datasheet in http://www.atmel.com/devices/at86rf212b.aspx?tab=documents . [4] at24mac602 datasheet in http://www.atmel.com/devices/at24mac602.aspx . [5] ms - 147 series interface rf connector with switch, 3.9mm high, dc to 6ghz http://www.hirose.co.jp/cataloge_hp/e35801505.pdf .
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 6 2. zigbit module o verview 2.1 overview the atzb - rf -2 12b -0- cn zigbit is a compact, low- power, high sensitivity ieee 802.15.4/zigbee oem module. based on a solid combination of the latest atmel mcu wireless hardware platform, 900mhz ism band transceiver and atmel studio wireless composer - the zigbit offers an unmatched combination of superior radio performance, ultra - low power consumption and exceptional ease of integration. figure 2 - 1. atzb -rf -2 12b -0- cn user i nterface d iagram this zigbit module contains the atmel at86 rf212b 900 mhz ism band transceiver for zigbee and ieee 802.15.4 [1] . the compact all - in - one board design of radio transceiver with very minimal components on the rf path to antenna connector dramatically improves the zigbits compact size, range performance on signal transmission and increases its sensitivity. this ensures stable connectivity within a larger coverage area, and helps develop applications on smaller footprint. the ms - 147 connector [5] can be used as an rf test port. zigbit module contains a complete rf design with all the necessary passive components included. the module can be easily mounted on a simple 2- layer pcb with a minimum of required external connection. the zigbit module evaluation kit containing the zigbit extension board for the atmel xplained pro hw evaluation platform can be used to develop fw using the atmel studio and evaluate using the wireless composer. compared to a custom rf/mcu solution, a module - based solution offers considerable savings in development time and nre cost per unit during the hw/fw design, prototyping, and mass production phases of product development. depending on end- user design requirements, the zigbit can operate as a sensor node, where it can be paired with a host processor driving the module over a serial interface.
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 7 the mac stack running on the host processor can then control data transmission. thus very minimal firmware customization is required for successful module design - in. third- party sensors can then be connected directly to the host mcu. every zigbit module come pre loaded with atmel assigned 64 - bit mac address stored in the eeprom built - in the modul e. this unique ieee mac address can be used as the mac address of the end product, so there is no need to buy a mac address separately for the product using the zigbit.
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 8 3. specification 3.1 electrical c haracteristics 3.1.1 absolute maximum r atings table 3 -1. absolute maximum r atings (1)(2) parameter minimum maximum voltage on any pin, except reset with respect to ground - 0.3v 3.6v (v dd max ) input rf level +10dbm current into v cc pins 200ma notes: 1. absolute maximum ratings are the values beyond which damage to the device may occur. under no circumstances must the absolute maximum ratings given in this table be violated. stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. this is a stress rating only. functional operation of the device at these or other conditions, beyond those indicated in the operational sections of this specification, is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. attention! zigbit is an esd- sensitive device. precaution should be taken when handling the device in order to prevent permanent damage. 3.1.2 power supply table 3 -2. test c onditions (unless otherwise stated), v cc = 3v, t amb = 25 c parameter range unit supply voltage, v dd 1.8 to 3.6 v current consumption: rx mode 9.3 ma current consumption: tx mode, pll on 5 ma current consumption: tx mode (1) C busy_tx C transmit state 26.9 ma current consumption: trx_off 6 17 a sleep current consumption: trx sleep 0. 7 a note 1: output tx power (when measuring consumption in tx mode) is + 9 dbm. current consumption depends on multiple factors, including but not limited to, the board design and materials . when this module is assembled on a base board, the mcu current also should be considered in estimating active and sleep currents of the product .
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 9 3.1.3 rf c haracteristics table 3 -3. rf c haracteristics (1) parameter condition range unit frequency band C fcc and industry canada (2) 902 C 928 m hz numbers of channels ( fcc and industry canada ) 10 channel spacing (fcc and industry canada) 2 mhz frequency band C etsi (european union) (2) 863 C 870 mhz number of channels (european union) 1 transmitter output power adjusted in 36 steps - 25 to +11 dbm receiver sensitivity per = 1% -103 dbm on - air data rate 20 up to 1000 kbps tx output/ rx input nominal impedance for balanced 50 range (us band) (3) open field, los, elevated 180 C 730 m range (euro band) (3) open field, los, elevated 140 C 440 m table 3 -4. tx power s ettings phy_tx_pwr 3:0 register value power register setting [dbm] output power [dbm] ( typical values at rf connector) c0 11 8.59 c1 10 8.14 80 9 7.43 82 8 5.85 83 7 4.97 84 6 4.1 40 5 3.58 86 4 2.12 00 3 1.4 01 2 0.42 02 1 - 0.93 03 0 - 2.09 04 -1 - 3.16 27 -2 - 4.29 91 -6 - 7.86 0d -10 - 12.27 15 -18 - 19.51 1d -25 - 26.82 note 1: for detailed characteristics, refer to [3] . note 2: appropriate fw (register selection) must be used for operating this zigbit in united states, canada, and european union. note 3: range measured is line of sight and at 10ft elevation from ground at different combinations of orientations of transmitter and receiver, with special conditions were there is minimal or no rf interference from other sources. for best case orientation o f the zigbits to achieve maximum range, refer to section 3.4 .
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 10 3.2 physical/environmental characteristics and o utline table 3 -5. physical characteristics parameters value comments size 3 0.0 x 20.0 mm operating temperature range - 40c to +85c - 40c to +85c operational 3.3 pin configuration table 3 -6. atzb -rf -2 12b -0-cn pinout d escription pin o ut pin descriptions function 1 avss analog ground 2 avss analog ground 3 devdd digital power input pin 4 devdd digital power input pin 5 rst reset active low 6 sel spi select, active low 7 mosi spi data input 8 miso spi data output 9 sclk spi clock 10 dig1 reserved 11 fem_csd reserved 32 dig3 rx tx indication 33 dig4 rx tx indication (inverted) 34 dig2 tx - rx time - stamp 35 slp_tr controls sleep, deep sleep, transmit start, receive states; active high 36 scl twi - eeprom 37 sda twi - eeprom 38 fem_cps reserved 39 clkm master clock out put 40 irq interrupt request signal output 41 dvss digital ground 42 dvss digital ground
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 11 3.4 antenna orientation r ecommendation the antenna in this module is designed to provide the best possible los range in the direction indicated in this illustration. 3.5 mounting i nformation figure 3 -1 shows the pcb pinout of a zigbit module. neither via- holes nor wires are allowed on the pcb upper layer in the area occupied by the module. as a critical requirement, rf_gnd pins should be grounded via several via - holes to be located right next to the pins thus minimizing inductance and preventing both mismatch and losses. figure 3 - 1. atzb -rf -2 12b -0- cn dimensions and pinout
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 12
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 13 figure 3 - 2. atzb -rf -212b -0- cn mounting information (preferred p lacement) figure 3 - 3. atzb -rf -212b -0- cn mounting information ( a lternative p lacement)
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 14 3.6 soldering p rofile the j - std - 020c - compliant soldering profile is recommended according to table 3 -7 . table 3 -7. soldering p rofile (1) profile feature green package average ramp - up rate (217c to peak) 3c/s max . preheat temperature 175c 25c 180s max . temperature maintained above 217c 60s to 150s time within 5c of actual peak temperature 20s to 40s peak temperature range 260c ramp - down rate 6c/s max . time within 25c to peak temperature 8 minutes note: 1. the package is backward compatible with pb/sn soldering profile.
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 15 4. s chematics ? connector schematics
pia101 pia102 coa1 pib101 pib102 pib103 pib104 pib105 pib106 cob1 pic101 pic102 coc1 pic201 pic202 coc2 pic301 pic302 coc3 pic401 pic402 coc4 pic501 pic502 coc5 pic601 pic602 coc6 pic701 pic702 coc7 pic801 pic802 coc8 pic901 pic902 coc9 pic1001 pic1002 coc10 pic1101 pic1102 coc11 pij101 pij102 pij103 pij104 coj1 pil101 pil102 col1 pil301 pil302 col3 colabel1 copcb1 piq101 piq102 piq103 piq104 coq1 pir101 pir102 cor1 pir201 pir202 cor2 pir301 pir302 cor3 pir501 pir502 cor5 pir601 pir602 cor6 piu101 piu102 piu103 piu104 piu105 piu106 piu107 piu108 piu109 piu1010 piu1011 piu1012 piu1013 piu1014 piu1015 piu1016 piu1017 piu1018 piu1019 piu1020 piu1021 piu1022 piu1023 piu1024 piu1025 piu1026 piu1027 piu1028 piu1029 piu1030 piu1031 piu1032 piu1033 cou1 piu201 piu202 piu203 piu204 piu205 cou2 piz101 piz102 piz103 piz104 piz105 piz106 piz107 piz108 piz109 piz1010 piz1011 piz1032 piz1033 piz1034 piz1035 piz1036 piz1037 piz1038 piz1039 piz1040 piz1041 piz1042 coz1 piz201 piz202 piz203 piz204 coz2 pic701 pil301 piu1028 pic301pir101 piz1039 piu109 piz1010 piu1010 piz1034 piu101 piz1032 piu102 piz1033 pib102 pib105 pib106 pic101 pic202 pic302 pic402 pic501 pic602 pic702 pic801 pic901 pic1102 pij103 pij104 piq102 piq104 piu103 piu106 piu107 piu1012 piu1016 piu1018 piu1021 piu1027 piu1030 piu1031 piu1032 piu1033 piu202 piu205 piz101 piz102 piz1041 piz1042 piz201 piz202 piz203 piz204 piu1024 piz1040 pir601 piu201 piz1036 pir501 piu203 piz1037 piu1020 piz108 piu1022 piz107 piz1038 piz1011 pir302 pir202 pir301 pir102 piu1017 pic1002 pij101 pic802 piq101 piu1026 pic601 piu1029 pic502 piq103 piu1025 pic401 pij102 pil101 pic102 piu1013 piu1014 pib101 pic1001 pia102 pir201 pia101 pic1101 pil102 piu1023 piz106 piu108 piz105 pib103 piu105 nlrf0n pib104 piu104 nlrf0p piu1019 piz109 piu1011 piz1035 pic201 pic902 pil302 pir502 pir602 piu1015 piu204 piz103 piz104 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 d d c c b b a a a08-1565 rfonly_212b.schdoc 1 1 14-jul-14 5:06:10 pm zigbit 900mhz rf-only atmel chennai rmz millenia 2 perungudi,chennai india page: of title: document number: revision: 3 date: ojs msk * gnd gnd reset_n slp_tr clkm dig3 dig4 irq nsel mosi sclk miso dig2 dig1 gnd gnd i pcb rule i pcb rule reset_n irq gnd gnd mac_scl mac_sda an_vcc_3v3 vcc_3v3 vcc_3v3 clkm vcc_3v3 dig4 2 avss 3 rfp 4 rfn 5 avss 6 dvss 7 /rst 8 dig1 9 dig2 10 slp_tr 11 dvss 12 dvdd 13 dvdd 14 devdd 15 dvss 16 clkm 17 dvss 18 sclk 19 miso 20 dvss 21 mosi 22 /sel 23 irq 24 xtal2 25 xtal1 26 avss 27 evdd 28 avdd 29 avss 30 avss 31 avss 32 dig3 1 pad 33 at86rf212b-zu u1 gnd gnd 50ohm 1 gnd 2 bal 3 bal 4 gnd 5 gnd 6 0896fb15a0100 b1 gnd slp_tr mac_scl mac_sda dig2 miso mosi sclk nsel gnd 0r r2 0r r3 gnd 2 sda 3 scl 1 wp 5 vcc 4 at24mac602-stum-t u2 vcc_3v3 gnd z igbit sub-ghz rf-only board pcb pcb1 an_vcc_3v3 vcc_3v3 blm15bb221sn1 l3 1uf c6 1uf c7 1uf c1 1uf c2 2.2 pf c3 10 pf c5 10 pf c8 100n c9 10 k r5 10 k r6 680r r1 product number/revision serial number l abel pcba l abel1 rf_n rf_p feed point 1 nc 2 0915at43a0026 a1 rf_in 1 rf_out 2 gnd 3 gnd 4 ms147 j1 gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd gnd 68pf c10 gnd 1 nrst 5 vdd 3 gnd 2 dig2 34 slp_tr 35 scl 36 sda 37 miso 8 mosi 7 nsel 6 fem_sel 38 gnd 41 vdd 4 irq 40 gnd 42 clkm 39 sclk 9 dig1 10 fem_csd 11 dig4 33 dig3 32 atzb-rf-4-0-c-915 z1 dig1 dig3 dig4 1 3 2 4 16.0mhz q1 1 2 3 4 emi shield z2 b a 5.6pf c11 5.6pf c4 2.7 nh l1 place de-coupling closer to trx place de-coupling closer to trx place xtal circuit closer to trx . isolate from digital signals. l ayout: maintain two g round planes and two power planes
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 17 4.1 handling instructions the zigbit modules are fixed with an emi shield to ensure compliance to emission and immunity rules. this shield is galvanic and not air tight. so cleaning of the module with ipa / other similar agents is not advised. humidity protection coating (conformal) will cause deviated rf behavior and coating material being trapped inside emi shield. so this should be avoided. for products requiring conformal coating, it is advised to suitably mask the zigbit before applying the coating to rest of the zigbit carrier board. to protect zigbit from humidity, the housing of the product should ensure suitable ingress protection standards are complied with. the ufl rf connector should never be exposed to varnish / similar conformal coating material which will affect electrical connection on the surfaces of connector. the in - built chip antenna has been tuned for the particular design . 4.2 general r ecommendations ? metal enclosure should not be used. using low profile enclosure might also affect antenna tuning . ? placing high profile components next to antenna should be avoided ? having holes/vias punched around the periphery of the board eliminates parasitic radiation from the boa rd edges also distorting antenna pattern ? zigbit module should not be placed next to consumer electronics which might interfere with zigbit's rf frequency band
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 18 5. persistence memory a dedicated memory space is allocated to store product specific information and called the persistence memory. the organization of the persistence memory is as follows: table 5 -1. persistence memory data size structure revision 2 bytes mac address (1) 8 bytes board information overall 49 bytes board information C pcba name 30 bytes board information C pcba serial number 10 bytes board information C pcba atmel part number 8 bytes board information C pcba revision 1 byte reserved 3 bytes xtal calibration value 1 byte reserved 7 bytes reserved 4 bytes crc 1 byte note: 1. the mac address stored inside the at24mac602 is a uniquely assigned id for each zigbit and owned by atmel. user of the zigbit application can use this unique mac id to address the zigbit in end - applications. the mac id can be read from the zigbit using the performance analyzer application that is supplied through atmel studio gallery extension. atzb - rf -2 12b -0- cn zigbit contains at24mac602, which has a globally unique mac address that can be assigned as the physical address of a system hardware device or node. persistence memory is stored in the first - half of the standard 2k bit eeprom of at24mac602 starting from address 0x00. special commands are available to read the unique 64- bit mac id and the persistent memory via the i 2 c compatible (2 - wire) serial interface (see section device addressing in at24mac602 [4] for details) .
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 19 6. ordering information table 6 -1. ordering i nformation part number description atzb -rf -2 12b -0- cn 900 mhz ieee802.15.4/zigbee oem module based on at86 rf212b transceiver with ufl rf connector, single unit atzb -rf -2 12b -0- cn r 900 mhz ieee802.15.4/zigbee oem module based on at86 rf212b transceiver with ufl rf connector, tape & reel note: tape & reel quantity: 200.
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 20 7. agency certifications 7.1 united states (fcc) this equipment complies with part 15 of the fcc rules and regulations. to fulfill fcc certification requirements, an oem manufacturer must comply with the following regulations: 1. the atzb - rf -2 12b -0- cn modular transmitter must be labeled with its own fcc id number, and, if the fcc id is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. this exterior label can use wording such as the following: important : contains fcc id: vw4a091743. this equipment complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (fcc 15.19). the internal antenna used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. ins tallers must be provided with antenna installation instructions and transmitter operating conditions for satisfying rf exposure compliance. this device is approved as a mobile device with respect to rf exposure compliance, and may only be marketed to oem installers. use in portable exposure conditions (fcc 2.1093) requires separate equipment authorization. important : modifications not expressly approved by this company could void the user's authority to operate this equipment (fcc section 15.21). important : this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (fcc section 15.105). 7.2 european union (etsi) the atzb - x0 - 256 -3-0- c module has been certified for use in european union countries. if these modules are incorporated into a product, the manufacturer must ensure compliance of the final product to the european harmonized emc and lowvoltage/safety standards. a declaration of conformity must be issued for each of these standards and kept on file as described in annex ii of the r&tte directive. furthermore, the manufacturer must maintain a copy of the modules' documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. if any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards.
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 21 important : the 'ce' marking must be affixed to a visible location on the oem product. the ce mark shall consist of the initials "ce" taking the following form: the ce marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. the ce marking must be affixed visibly, legibly, and indelibly. more detailed information about ce marking requirements you can find at "directive 1999/5/ec of the european parliament and of the council" on 9 march 1999 at section 12. 7.3 industry canada ( ic) compliance statements this device complies with industry canada licence - exempt rss standard(s). operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includi ng interference that may cause undesired operation of the device. le prsent appareil est conforme aux cnr d'industrie canada applicables aux appareils radio exempts de licence. l'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. this equipment complies with radio frequency exposure limits set forth by industry canada for an uncontrolled environment. this equipment should be installed and operated with minimum distance 20cm between the device and the user or bystanders. cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par industrie canada pour un environnement non contr?l. cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre le dispositi f et l'utilisateur ou des tiers. caution: any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. the oem integrator is still responsible for testing their end - product for any additional compliance requirements required with this module installed (for example, digital device emissions, pc peripheral requirements, etc.). this module is labelled with its own ic id. if the ic id certification number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. in that case, the final end product must be labelled in a visible area with the following: contains transmitter module ic: 11019a - 091743 or contains ic: 11019a - 091743 ce module est tiquet avec son propre id ic. si le numro de certification ic id n'est pas visible lorsqu'il est install l'intrieur d'un autre appareil, l'appareil doit afficher l'tiquette sur le module de rfrence ci - joint. dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant: contains transmitter module ic: 11019a - 091743 or contains ic: 11019a - 091743
atzb - rf -2 12b -0- cn [ zigbit 900mhz wireless modules ] 42269b ? wireless ? 07/2014 22 8. revision h istory doc. rev. date comments 42269 b 07/2014 the schematic on page 16 has been updated 42269a 04/2014 initial document release
atmel corporation 1600 technology drive san jose, ca 95110 usa tel: (+1)(408) 441 - 0311 fax: (+1)(408) 487 - 2600 www.atmel.com atmel asia limited unit 01 - 5 & 16, 19f bea tower, millennium city 5 418 kwun tong road kwun tong, kowloon hong kong tel: (+852) 2245 - 6100 fax: (+852) 2722 - 1369 atmel munich gmbh business campus parkring 4 d - 85748 garching b. munich germany tel: (+49) 89 - 31970 -0 fax: (+49) 89 - 3194621 atmel japan g.k. 16f shin - osaki kangyo building 1 -6- 4 osaki , shinagawa-ku tokyo 141 - 0032 japan tel: (+81)(3) 6417 - 0300 fax: (+81)(3) 6417 - 0370 ? 201 4 atmel corporation. all rights reserved. / rev.: 42269b ? wireless ? 07/2014 atmel ? , atmel logo and combinations thereof, avr ? , bitcloud ? , enabling unlimited possibilities ? , zigbit ? , and others are registered trademarks or trademarks of atmel corporation or its subsidiaries. other terms and product names may be trademarks of others. disclaimer: the information in this document is provided in connection with atmel products. no license, express or implied, by estoppel or otherwise, to any intellectual pro perty right is granted by this document or in connection with the sale of atmel products. except as set forth in the atmel terms an d conditions of sales located on the atmel website, atmel assumes no liability whatsoever and disclaims any express, implied or statutory warranty relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or non - infringement. in no event shall atmel be liable for any direct, indirect, consequential, punitive, special or incidental damages (including, without limitation, damages for loss and profits, business interruption, or loss of in formation) arising out of the use or inability to use this document, even if atmel has been advised of the possibility of suc h damages. atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this docume nt and reserves the right to make changes to specifications and products descriptions at any time without notice. atmel does not make any commitment to update the information contained herein. unless specifically provided o therwise, atmel products are not suitable for, and shall not be used in, automotive applications. atmel products are not intended, authorized, or warranted for use as components in applications inte nded to support or sustain life.

▲Up To Search▲

Price & Availability of ATZB-RF-212B-0-CN-14

	To Download ATZB-RF-212B-0-CN-14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .